Hebei Province, Wu County five the welding equipment factory. Production and sales: spot welding machine, pneumatic spot welding, nuts, spot welding machine, welding machine, seam welding machine, welding machine, copper rod welder, aluminum welding machine, band saw blade welding machine, thread rolling machine , bar straightening machines, wire welding machine, wire welding machine, copper wire welding, aluminum welding machine, the cages spot welder, spot welder steel and can be customized according to custom make all kinds of special special equipment . Welcome to inquire: Contact: Yu Zhendong. Tel :0318 -3727375. Mobile: 15512963508. Website: www.buydhj.com Steel Bar Straightening and Cutting Machine; This product is according to the user needs and the needs of new and improved products for many years, fully functional, fully automatic, straight, cut off, cut to length, praised by users over the years . The working procedures of the cold Roberts manually from the mouth of the feed through the rollers and cutter, and then according to the size of the diameter of the cold Roberts adjusting the angle right, give the power. Note: before work to check all the screws and must Luo tight. The straight wire machine has reasonable structure, easy to operate, safe and reliable, suitable for cages, rabbit cage, construction mesh, all kinds of wire, Reinforcing wire inserted truncated shaped mesh wire straightening. Two main technical parameters and performance indicators Specifications productivity cut off the length of the host re-power Dimensions 2mm-4mm 30 m / min on demand 150KG 2.25KW 4000 * 280 * 1000 3mm-6mm 30 meters / min required 150KG 2.25KW 4000 * 280 * 1000 4mm-8mm 30 m / min requirements 200KG 7.5KW 5000 * 300 * 1200 6mm-10mm 30 meters minutes required 350KG 7.5KW 5000 * 300 * 1200 8mm-12mm 30 m / min on demand 500KG 5000 * 300 * 1200 structure Introduction The aircraft structure by high-speed rotor rotation adjustment angle of straight wire mode, to straighten the effect, then forward hundred hundred wire wheel wire. Required size is reached, the wire hit the positioning key runway advance forward 5 mm punch above to suppress vertical shred knife immediately cut off the wire by vertical wire cutter platen press and hold the opening bearings, wire automatically fall to Tuosi frame, if you want to change the length, mobile positioning key installation and commissioning of the first body on the basis of a flat, and then the motor switch connected to the power supply, and then move the switch handle, If Diao wire wheel rotation in the wrong direction on changing the motor into the line connector. 2, all rotating parts to add a good oil, butter. 3, before starting guard should be put down, check the motor connector is leakage. To connect the ground wire straightening machine body. 4, idle for 2-3 minutes, then to penetrate the wire in the high speed rotor, hold down the wire, the wire gripper wheel shredded knife holes in the penetration of a cross. 5 to adjust the size of high-speed rotor angle adjustment mode, can work to achieve the effect of straight wire. Use and maintenance of a boot must be familiar with the manual, in accordance with the provisions of the add oil, check all fasteners are tightened, Diao wire the direction of rotation of the wheel against the required direction, the problem please. 2, check the cross-sectional wire cutter on the nut is loose, the cross shred knife vertical shredded knife gap modulation as small as possible, but not too tight, generally able to slide up and down is appropriate, the upper punch and the vertical shredded knife upper and lower gap is generally 2-3mm, upper punch with H shredded knife pressure is generally the amount of 4-5mm. Hand touch straightening wire feel a small bend, straightening mode angle, put the adjustment expense smaller, if there is a big bend, it is necessary to adjust the die angle increases, if not straight, necessary to check the the Diao wire wheel speed rotor, with the cross-cutting knife hole is horizontal position, these three points must be first-line, so can not deviate from the level. (4) If a broken wire, it is necessary to check the compression spring the Diao wire wheel pressure is not tight or groove badly worn the Diao wire wheel, adjust the the Diao wire wheel pressure tank or not, it is necessary to change Diao wire wheel on the groove. 5, if there is broken wire head burr, may be if they had broken wire knife gap is too large, it is necessary to adjust the horizontal and vertical knife gap, if that does not work, check whether the horizontal and vertical knife serious wear and tear, if badly worn, put the knife vertical broken wire and the cross-sectional remove the screwdriver, cross-sectional wire cutter polished alloy wheels, the vertical broken wire knife in general grinding wheel is polished until it is sharp. 6, if there is a continuous cut, may be the extension spring over to send to adjust the tightness of the extension spring, compression spring is Diao wire wheel to send, can not push the runway you need to adjust the the Diao wire wheel compression spring. In short, the actual circumstances. Contact: Yu Zhendong. Mobile: 15512963508. Website: www.buydhj.com